8 Most Common Electrical Wiring Code Violations In Your Home
Every day, we see new DIYers and home remodelers trying their hand at electrical work. They usually do not know the rules for doing this type of work in Minnesota or the consequences if they don’t follow them.
Pay attention to the most common violations of the electrical wiring code and avoid making these mistakes. But first…
What is the National Electrical Code?
The National Electrical Code (NEC) is a safety code that establishes the minimum requirements for safe electrical installations in the United States. It sets out rules to ensure:
Fire and flashover prevention
People are protected from electric shock
The equipment operates at an acceptable voltage level
Increased capacity of electrical distribution systems
Enhanced reliability of supply service interruptions or failures during emergencies
Efficient energy use by providing clear guidance on overloading circuits with multiple appliances without causing fire hazards
The NEC also provides standards for grounding and bonding installations within buildings or their yards if they have metallic power system enclosures or underground cable vaults, even when there are no ground-fault circuit interrupters installed.
The Ultimate Importance of Meeting Electrical Code
Whether you’re a frequent DIYer at home or are a professional electrician, following these stringent electrical codes ensures your safety and the safety of others. It also protects you from fines and other penalties should an electrical inspection find that the work done was not up to code.
Common Electrical Wiring Violations + How to Avoid
You may be wondering why there are so many frequent violations? There is often a lot of confusion when it comes to electrical wiring, especially in Minnesota, where we have two different codes (NEC 2020 & MN Electrical Code). It can be hard for homeowners with limited knowledge of electricity and apprentice electricians alike to tell which code they need to follow.
This means that even someone who knows what they’re doing might accidentally do something wrong without realizing it—or worse, knowingly break one rule but ignore another because they don’t know about them!
Here’s how to meet code every time.
1 – Don’t Forget GFCI Protection in the Proper Rooms 🚪
Ground-fault circuit interrupters (GFCIs) help keep people safe from electrical shocks. GFCI receptacles (outlets) shut off the power to a device if something goes wrong with it or someone gets shocked, protecting them from injury. Minnesota requires all bathrooms, kitchens, garages, crawl spaces, and unfinished basements to have ground fault protection installed in those areas of the house where water or moisture could come into contact with an energized part of the system.
2 – Only Install Bathroom Light Fixtures Rated for Wet or Damp Conditions 🚱
If you install a light fixture in your bathroom, make sure it is rated for damp environments. This will ensure that no water can get into the electrical components of the light and cause damage to them if they are submerged or splashed by accident. Light fixtures located near the shower must be rated for wet locations.
3 – Never Fail to Have a Dedicated 20-Amp Circuits for all Appliances 📺
Every room in your house needs to have its own 20-amp circuits—some require more than one.
Every bathroom needs one circuit for the receptacles and one for the lighting.
If your bathroom has a heated vent fan in the shower, that must also have a 20-amp circuit.
Kitchens require at least two 20-amp circuits dedicated to small appliances.
Your kitchen lighting, garbage disposal, dishwasher, fridge, stove, microwave, and any other major appliances must each have their own 20-amp or 120-volt circuits.
Depending on how many outlets there are and how much power must be supplied, your living room, dining room, and bedrooms need just one dedicated circuit each.
Your garage and laundry room also require their own circuit. Note: if you have an electric dryer, you must have at least a 30-amp or 240-volt circuit with four conductors to ensure it runs safely and efficiently.
4 – You Must Have GFCI Protected Outlets Near Any Sink 🔌 ⚡️
If you have receptacles within 6-feet of your bathroom or kitchen sink, they need to be GFCI protected. Also, all countertop receptacles require GFCI protection and be placed no closer than every 4 feet. Failing to do so means a sure-fire chance of electric shock using hair tools near open water.
5 – Install Proper Lighting in the Stairways 🤕
If you install a new light fixture in your stairwell, make sure it is an approved lighting assembly and not just a bare light bulb. Stairway electrical code also requires 3-way switches at the top and the bottom and adequate lighting on any landing. This will ensure people coming down or going upstairs can see where they’re going and prevent significant injury.
6 – Install Outlets Every 10 Feet in Every Hallway 🔌
Any hallway longer than 10 feet need at least one receptacle outlet installed. Hallways also suggest three-way switches at each end like a stairway, but this may change depending on how long the hallway is.
7 – Never Leave Exposed Incandescents in the Closet 💡🚪
Incandescent light bulbs can get very hot, so they must have a light cover. If your closet lighting is recessed, it can be 6 inches away from any upper closet storage (clothes, boxes, etc.), but all other light fixtures must be at least 12 inches from storage.
8 – Ensure Correct Main Circuit Breaker Ratings ✅
The main breaker for your electrical panel determines how many circuits can go into it (and thus what size of breakers are needed). If you’re unsure which breaker is your “main” one—it’ll likely say something like “MAIN BREAKER” on the label. You may need more than one if all your rooms require their own circuits.
Where Do I Find Specific Local Electrical Codes?
You can either contact 4Front Energy, and we can help you find out more information, or visit the MN Department of Labor and Industry website. Here is the most recently updated Electrical Inspection Checklist for 2020 (updated every three years).
We also have some handy articles with the dos and don’ts of DIY electrical, which can also help you. It’s always best to check before doing any work yourself since there are many ways code violations could happen unintentionally without realizing it until after the project is completed.
Why Choose 4Front Energy?
We’re a Service Company, Not a Sales Company
- Licensed, bonded & insured contractor
- Trusted Twin Cities service provider for nearly 30 years
- Reliable service excellence
- One number for electric, HVAC, and plumbing
- Stand behind our work with integrity
- Fair and straightforward pricing
- Provide invaluable comfort and integrated efficiency
- Technicians that take pride in their work